Brodit
Brodit 513567 Active holder 513567
- UPC:
- 0000000000000
- MPN:
- 513567
- Condition:
- New
- Availability:
- Available to Order: 3 - 4 weeks leadtime
Description
Active holder for fixed installation
With tilt swivel, with Molex adapter system. 2A charger. Fits devices with standard and extended battery.
An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!
You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection. Attach onto a ProClip Mounting Platform.
INSTALLATION INSTRUCTIONS:Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters. Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. How to mount the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Screw a few turns on the screw, just so the thread starts to pull. Pull the holder toward you and hold it slightly tensed, in the same time tighten the screw so the holder is pulled toward the tilt swivel. Tighten the screw firm at first, then loosen it a bit so the holder is firmly in place, but still can be adjusted. 4. The holder is in place.
Design
Compatibility
Datalogic LYNX
Mobile device type
Terminal
Product colour
Black
Proper use
Car
Type
Active holder
Multimedia
Built-in speaker(s)
Yes
Package dimensions
Gross Weight (Package, kg)
0.25 kg
Product dimensions
Net Weight (Product, kg)
0.2 kg
Vendor information
Brand Name
Brodit
Homepage
http://www.brodit.se/product.html?locale=se&id=513567
Warranty
1 Year(s)
View AllClose
With tilt swivel, with Molex adapter system. 2A charger. Fits devices with standard and extended battery.
An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!
You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection. Attach onto a ProClip Mounting Platform.
INSTALLATION INSTRUCTIONS:Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters. Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle. How to mount the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Screw a few turns on the screw, just so the thread starts to pull. Pull the holder toward you and hold it slightly tensed, in the same time tighten the screw so the holder is pulled toward the tilt swivel. Tighten the screw firm at first, then loosen it a bit so the holder is firmly in place, but still can be adjusted. 4. The holder is in place.
Design
Compatibility
Datalogic LYNX
Mobile device type
Terminal
Product colour
Black
Proper use
Car
Type
Active holder
Multimedia
Built-in speaker(s)
Yes
Package dimensions
Gross Weight (Package, kg)
0.25 kg
Product dimensions
Net Weight (Product, kg)
0.2 kg
Vendor information
Brand Name
Brodit
Homepage
http://www.brodit.se/product.html?locale=se&id=513567
Warranty
1 Year(s)
Additional Information
Shipping: |
Available to Order - Call for ETA |
Delivery: |
Available to Order - Call for ETA |
Related Products
Brodit 536577 Active Holder - Brodit 536577
Brodit
£147.11
Holder with lock.
Active holder for fixed installation. With tilt swivel. 2 keys included. This holder is to be used when you will secure your iPad and still have it easy accessable. Perfect for use...
Brodit 521663 Active Holder - Brodit 521663
Brodit
£113.29
With tilt swivel. With USB cable. Apple approved charging cable. Fits devices with skin.
Use an active holder for your Apple device on the road and you will always have a freshly charged battery! In...
Brodit 527942 Active holder for 527942
Brodit
£97.04
This holder is crash tested and approved for use with device without skin/case on Brodit's headrest mount.
Measure your device/skin/case and compare with specifications. Fits for devices...
Brodit 512637 Active holder 512637
Brodit
£59.04
With tilt swivel.
Use an active holder for your Tab 4 while driving and you will always have a freshly charged battery! The holder provides a neat and comfortable installation - safe and convenient...
Brodit 712038 Active holder 712038
Brodit
£49.54
Keep your phone's battery fully charged in an active holder, always within easy sight and reach! Neat, discreet and convenient. Custom made with a perfect, firm fit. With cig-plug cable, 2A charging...
Brodit 512567 Active holder 512567
Brodit
£71.39
Active holder with cig-plug
With tilt swivel. Fits devices with standard and extended battery.
The active holder charges your battery when it is in the holder. The charging device connects to the...
Brodit 513636 Active holder 513636
Brodit
£76.71
With tilt swivel, with Molex adapter system.
Use an active holder for your Tab 4 while driving and you will always have a freshly charged battery! The active holder is to be connected inside the...
Brodit 727132 Active holder 727132
Brodit
£76.71
Use an active holder for your Tab A 10.1 while driving and you will always have a freshly charged battery! The active holder is to be connected inside the dashboard. It provides a discreet and neat...
Brodit 513921 Active holder 513921
Brodit
£130.86
Robust active holder with rugged design to withstand rough handling in professional everyday use. Keeps your device extra securely in place in the holder. Thanks to the swiveling top part which...